Graco 313879B Manual do Utilizador

RepairThermoLazer™ Pavement Marking System- For professional application of thermoplastic traffic marking compound materials(reflective beads applied

Adjust Gas Pressure to Kettle Burners 10 313879BAdjust Gas Pressure to Kettle Burners1. Shut off kettle gas safety valve (CC).2. Turn kettle temperatu

Adjust Kettle Pilot Burner Flame313879B 11Adjust Kettle Pilot Burner Flame1. Ignite kettle gas pilot burner.2. Record pilot burner flame height and co

Cleaning Kettle Main Burner Gas Lines 12 313879BCleaning Kettle Main Burner Gas Lines1. Disconnect gas tubing line (49) from gas tube fitting tee (165

Replacing Screed Box Spring313879B 13Replacing Screed Box Spring1. Position replacement spring as shown below and slide into spring guard.2. Push spri

Securing Bead Dispenser Wheel 14 313879BSecuring Bead Dispenser WheelTo properly dispense beads, drive wheel (27) must be in direct contact with tire

Screed Box/Bead Dispenser Box Actuator313879B 15Screed Box/Bead Dispenser Box ActuatorIf the screed box/bead dispenser box actuator does not remain in

Troubleshooting 16 313879BTroubleshootingProblem Cause SolutionKettle pilot burner does not ignite or does not remain ignitedLow or empty LP-gas tank

Troubleshooting313879B 17Kettle main burners do not ignite or are not burning correctlyKettle gas safety valve knob not at correct positionTurn knob t

Troubleshooting 18 313879BSmartDie™ screed box IR burner does not ignite, does not remain ignited, or can not change heat outputEmpty LP-gas tank Repl

Troubleshooting313879B 19SmartDie™ screed box leakingForeign material in screed box discharge openingCAREFULLY dislodge and remove foreign material.Di

Table of Contents 2 313879BTable of ContentsTable of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 2Warnings . . . . . . . . . . .

Troubleshooting 20 313879BApplying MaterialProblem Cause SolutionRagged line edges when extruding Dirty screed box CAREFULLY clean box. Discharge open

Troubleshooting313879B 21Ragged edges and gaps in line • Material temperature is too low• Thermolazer™ speed is too fast• Raise material temperature•

Technical Data 22 313879BTechnical DataDimensionsFuel: Liquefied petroleum gas (LP-gas) (propane vapor)Gas supply pressure (maximum): 250 psi (17.24

Graco Standard Warranty313879B 23Graco Standard WarrantyGraco warrants all equipment referenced in this document which is manufactured by Graco and be

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves th

Warnings313879B 3WarningsThe following are general warnings related to the safe setup, use, grounding, maintenance and repair of this equip-ment. In t

Warnings 4 313879BTOXIC FLUID OR FUMES HAZARD Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or

Kettle Gas Safety Valve, Kettle Temperature Control, and Kettle Thermopile Diagnosis313879B 5Kettle Gas Safety Valve, Kettle Temperature Control, and

Kettle Temperature Control Calibration 6 313879BKettle Temperature Control CalibrationTo Check Kettle Temperature Control Calibration:1. Move Thermola

Kettle Thermometer Calibration313879B 7Kettle Thermometer CalibrationTo Check Kettle Thermometer Calibration:1. Move ThermoLazer™ to an area with no w

Thermopile Replacement 8 313879BThermopile ReplacementRemoval1. Shut off gas valve on LP-tank and disconnect hose.2. Remove gas safety valve enclosure

Thermopile Replacement313879B 9Installation1. Replace thermopile (7).2. Replace gas pilot mounting plate (18).3. Connect gas pilot line (76) at gas pi