Graco 17D163 Manual de Utilização e Manutenção

334659CENOperation, Parts210 ES Electric Airless SprayersFor professional use only.Not approved for use in explosive atmospheres or hazardous location

Pressure Relief Procedure 10 334659CPressure Relief ProcedureFollow the Pressure Relief Procedure whenever you see this symbol.1. Turn the ON/OFF swit

Pressure Relief Procedure334659C 116. Turn the prime valve down. Put drain tube in a pail. Leave prime valve in the down (drain) position until you ar

Setup 12 334659CSetupWhen unpacking sprayer for the first time orafter long term storage perform setupprocedure. When first setup is performedremove s

Setup334659C 136. When unpacking sprayer for the first time remove packaging materials from inlet strainer. After long term storage check inlet strain

Setup 14 334659C10. Turn prime valve down.11. Place fluid intake with drain tube in grounded metal pail partially filled with flushing fluid. See Grou

Startup334659C 15Startup1. Perform Pressure Relief Procedure, page 10.2. Turn pressure control to lowest pressure.3. Turn ON/OFF switch to ON position

Startup 16 334659C7. Hold gun against grounded metal waste pail. Trigger gun until paint appears.8. Move gun to paint pail and trigger for 20 seconds.

Operation334659C 17OperationSpray Tip Installation1. Perform Pressure Relief Procedure, page 10.2. Use spray tip (A) to insert OneSeal™ (B) into tip g

Operation 18 334659C3. Hold gun perpendicular, 10-12 in. (25-30 cm) from surface. Spray back and forth; overlap by 50%. 4. Trigger gun after moving. R

Operation334659C 19Cleanup1. Perform Pressure Relief Procedure, page 10.2. Remove tip guard and Spray Tip. For additional information, see separate gu

Contents 2 334659CContentsWarnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operation 20 334659C6. Increase pressure 1/2 turn to start motor. Hold gun against paint pail. Disengage trigger lock. Trigger gun and increase pressu

Operation334659C 2110. Turn prime valve horizontal. Trigger gun into flushing pail to purge fluid from hose.11. Engage trigger lock.12. Turn pressure

Maintenance 22 334659CMaintenanceRoutine maintenance is important to ensure proper operation of your sprayer. Maintenance includes performing routine

Troubleshooting334659C 23TroubleshootingMechanical/Fluid Flow1. Follow Pressure Relief Procedure, page 10, before checking or repairing.2. Check all p

Troubleshooting 24 334659CPump output is low Pump rod damage. Repair pump. See pump manual.Low stall pressure. Turn pressure knob fully clockwise. Mak

Troubleshooting334659C 25Fluid is spitting from gun Air in pump or hose. Check and tighten all fluid connections. Cycle pump as slowly as possible dur

Troubleshooting 26 334659CElectricalSymptom: Sprayer does not run, stopsrunning, or will not shut off.Perform Pressure Relief Procedure, page10.1. Plu

Troubleshooting334659C 27Check motor rotation. Perform a spin test by connecting a 9 –12 Volt battery to the motor leads. Motor leads may vary in styl

Troubleshooting 28 334659CCheck motor armature resistance.Connect the Red and Black leads from the motor to an Ohm meter. Rotate the motor while check

Troubleshooting334659C 29Sprayer will not shut off after reaching or exceeding maximum pressure.Check pressure control. Disconnect pressure control, i

Warnings334659C 3WarningsThe following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point sy

Stand Model Sprayer Parts 30 334659CStand Model Sprayer Parts59675454d364747231216556716354b54c54a536865ti25303aFrom ti24099a711See page36.24Ref. Torq

Stand Model Sprayer Parts334659C 314044254543416947426613222521270911437203960145ti25255a28278993143Ref. Torque140-160 in-lb (15.8 - 18.1 N•m)Hammer t

Stand Model Sprayer Parts 32 334659CStand Model Parts ListRef.Part DescriptionQty.7 115498 SCREW, mch, slot/hex, wash hd112 117501 SCREW, mach, slot h

Hi-Boy Sprayers Parts334659C 33Hi-Boy Sprayers Parts59472312564636635369746867ti25461a655454b54c54d754a141221Ref. Torque140-160 in-lb (15.8 - 18.1 N•m

Hi-Boy Sprayers Parts 34 334659C4341132623955456037148795701364022124742251374452ti25462a145282789934891143Ref. Torque140-160 in-lb (15.8 - 18.1 N•m)H

Hi-Boy Sprayers Parts334659C 35Hi-Boy Sprayers Parts ListRef. Part DescriptionQty.7 115498 SCREW, mch, slot/hex, wash hd112 117501 SCREW, mach, slot h

Control Box and Filter 36 334659CControl Box and Filter146150152424363527171816249561212972138153514526ti25463a15415587112Ref. Torque140-160 in-lb (15

Control Box and Filter334659C 37Control and Filter Parts ListRef. Part Description Qty.2 104361 PACKING, o-ring 14 111600 PIN, grooved 15 277364 GASK

Wiring Diagram 38 334659CWiring DiagramRed (+)Black (-)PressureControlAssemblyPowerPlugWhiteGreenBlackfrom Motor2 x YellowON/OFFSwitchti5643aCapacitor

Technical Specifications334659C 39Technical Specifications17D163, 17C305US MetricSprayerMaximum fluid working pressure 3000 psi 207 bar, 20.7 MPaMaxim

Warnings 4 334659CFIRE AND EXPLOSION HAZARDFlammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire

Graco Standard Warranty 40 334659CGraco Standard WarrantyGraco warrants all equipment referenced in this document which is manufactured by Graco and b

All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves th

Warnings334659C 5SKIN INJECTION HAZARDHigh-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that in

Warnings 6 334659CELECTRIC SHOCK HAZARDThis equipment must be grounded. Improper grounding, setup, or usage of the system can cause electric shock.• T

Component Identification334659C 7Component IdentificationStand ModelUKSMNVPRABDti25254aJGFLHA ON/OFF SwitchB Pressure ControlD Prime ValveF Tip GuardG

Component Identification 8 334659CHi-Boy Modelsti25465aJUKMNVPRTABDSGFLHA ON/OFF SwitchB Pressure ControlD Prime ValveF Tip GuardG Spray TipHGunJ Airl

Grounding334659C 9GroundingThis sprayer includes a ground wire with anappropriate ground contact.The plug must be plugged into an outlet thatis proper